Not joined yet? Register for free and enjoy features such as alerts, private messaging and viewing latest posts and topics.

Snapped drive belt

Discuss your latest mods or ideas, and anything to do with the BMW X5 (E53).
User avatar
AVI-8
Member
Member
Posts: 94
Joined: Sat Apr 26, 2014 12:09 am
Location: Ayrshire

Snapped drive belt

Post by AVI-8 » Sat Nov 12, 2022 12:11 pm

https://www.ebay.co.uk/itm/363772624896 ... media=COPY

That’s the E torx socket set you’ll need to turn the crank pulley, pretty sure it’s an E14
But just check before ordering, you’ll either have 4 of these or one 26mm bolt in the centre, you’ll be able to check by reaching down and feeling with your hand as you’re probably not going to see it from above.

cooa99
Member
Member
Posts: 290
Joined: Thu Aug 18, 2011 1:00 pm
Location: Bexleyheath

Snapped drive belt

Post by cooa99 » Sat Nov 12, 2022 3:30 pm

AVI-8 wrote: Sat Nov 12, 2022 12:11 pm https://www.ebay.co.uk/itm/363772624896 ... media=COPY

That’s the E torx socket set you’ll need to turn the crank pulley, pretty sure it’s an E14
But just check before ordering, you’ll either have 4 of these or one 26mm bolt in the centre, you’ll be able to check by reaching down and feeling with your hand as you’re probably not going to see it from above.
Much appreciated. Both belts now ordered from bmw. I'll try to take the fan off tomorrow once I get the fan spanner. If the fan does not come off then it will have to go to the mechanic.

User avatar
AVI-8
Member
Member
Posts: 94
Joined: Sat Apr 26, 2014 12:09 am
Location: Ayrshire

Snapped drive belt

Post by AVI-8 » Sat Nov 12, 2022 4:28 pm

I’ve just checked, It’s an E12 for the crank bolts
And yes it’s a 32 for the water pump, if you don’t have an adjustable spanner that goes up to 32mm this is about the cheapest I could find

https://www.ebay.co.uk/itm/252502895043 ... media=COPY

User avatar
marti
Member
Member
Posts: 770
Joined: Tue Jan 19, 2016 11:33 am
Location: Norfolk

Snapped drive belt

Post by marti » Sun Nov 13, 2022 12:17 pm

32mm spanner......go to a caravan/camping shop...gas bottle spanners are 31.8mm, so you just need to file/grind it out a bit....I have one from years ago and works fine and not a lot of money.....

cooa99
Member
Member
Posts: 290
Joined: Thu Aug 18, 2011 1:00 pm
Location: Bexleyheath

Snapped drive belt

Post by cooa99 » Mon Nov 14, 2022 12:56 am

AVI-8 wrote: Sat Nov 12, 2022 4:28 pm I’ve just checked, It’s an E12 for the crank bolts
And yes it’s a 32 for the water pump, if you don’t have an adjustable spanner that goes up to 32mm this is about the cheapest I could find

https://www.ebay.co.uk/itm/252502895043 ... media=COPY
I got back home late last night. Fan tool from amazon and 32mm Spanner from Halfords. The fan nut came straight off thought any effort. I still have to wait till Tuesday for both belts from bmw

Is yours a 3.0D? because your picture looks same as mine.

I am slightly lost on the E torx you mentioned because the pulley adjuster has a nut on it like in your picture hence not required?
Attachments
PIC1.jpg
PIC1.jpg (149.61 KiB) Viewed 930 times
AVI8.jpeg
AVI8.jpeg (155.37 KiB) Viewed 930 times

User avatar
henrym3
Snr Member
Snr Member
Posts: 1837
Joined: Wed May 25, 2016 11:07 pm
Location: Bournemouth

Snapped drive belt

Post by henrym3 » Fri Nov 18, 2022 6:10 pm

Things just used to be simpler. Back in the 70’s when the belt on my 850 mini broke I used the girlfriend’s tights to get us home. She wasn’t amused. You could say she overheated but at least the car didn’t.

Online
User avatar
X5Sport
Global Moderator
Global Moderator
Posts: 18520
Joined: Fri Sep 03, 2010 4:09 pm
Location: Planet X6......

Snapped drive belt

Post by X5Sport » Fri Nov 18, 2022 9:28 pm

:heat: :rofl: :rofl:

Looking at the routing, when Ford introduced the FWD Escort the 16V CVH engine cambelt went through two sequential 180° bends and Surrey Police had to start changing them every 3,000 miles! A significant number of cars with that engine suffered catastrophic engine failure (including the one I was driving with less than 6k on it from new). The drive belt on these cars seems to go through worse contortions but they last for years.
:ant: Never anthropomorphise computers. They hate that.

Leslie
Snr Member
Snr Member
Posts: 1275
Joined: Sat Sep 29, 2018 10:58 am

Snapped drive belt

Post by Leslie » Sat Nov 19, 2022 3:33 pm

That idler pulley is on a sprung arm just put a spanner or socket on it and it will rotate round to get the tension of the new belt , think mine was the same on my e70 when I changed the water pump :thumbsup:

cooa99
Member
Member
Posts: 290
Joined: Thu Aug 18, 2011 1:00 pm
Location: Bexleyheath

Snapped drive belt

Post by cooa99 » Tue Nov 22, 2022 5:02 pm

The socket that goes on the sprung arm is a 24mm. The big belt is now on hurray!

I tried to get the smaller belt that goes on the AC compressor of with no joy. There has to be a trick to stretching it over the two pulleys.

Leslie
Snr Member
Snr Member
Posts: 1275
Joined: Sat Sep 29, 2018 10:58 am

Snapped drive belt

Post by Leslie » Tue Nov 22, 2022 10:23 pm

These is a tool for the job without it will be a real struggle if you were changing it as I said cut it off is fastest way.. I used a piece of thick card to refit.

cooa99
Member
Member
Posts: 290
Joined: Thu Aug 18, 2011 1:00 pm
Location: Bexleyheath

Snapped drive belt

Post by cooa99 » Thu Nov 24, 2022 7:07 am

I have cut the old belt off. What do you mean by thick card?

Will this item this item help at all ?
https://www.amazon.co.uk/Lisle-59370-St ... p_s_a_1_1?

Leslie
Snr Member
Snr Member
Posts: 1275
Joined: Sat Sep 29, 2018 10:58 am

Snapped drive belt

Post by Leslie » Thu Nov 24, 2022 6:11 pm

That's the one though they should be cheaper than that ,ones on ebay 12 quid :thumbsup: . if you have a piece of old belt put it on the grooves too allow the new belt to run over it till its on the pulley problem on these is there is no crank pulley bolt to turn by hand just 4 little bolts but using one of them may be enough to rotate engine :thumbsup: The one I did on out focus was easier due to having a crank bolt to spanner after I snipped old belt to get it out the way , I didn't need to take x5 one off just slipped main belt of as I was only changing water pump :D

to be fair for 12 quid just buy the tool and you will always have it :driving:

cooa99
Member
Member
Posts: 290
Joined: Thu Aug 18, 2011 1:00 pm
Location: Bexleyheath

Snapped drive belt

Post by cooa99 » Thu Nov 24, 2022 6:39 pm

I’ll order that from ebay. I’m almost certain i saw a plastic version of it which means it could be 3d printed, same as a tool to turn the AC pulley.

I have a 3d printer but crap at design. Maybe there is a money maker idea here 😀

Leslie
Snr Member
Snr Member
Posts: 1275
Joined: Sat Sep 29, 2018 10:58 am

Snapped drive belt

Post by Leslie » Thu Nov 24, 2022 8:48 pm

There are plastic ones for 6 quid on the bay cheap as chips now :driving:

cooa99
Member
Member
Posts: 290
Joined: Thu Aug 18, 2011 1:00 pm
Location: Bexleyheath

Snapped drive belt

Post by cooa99 » Sat Nov 26, 2022 5:44 pm

Well I give up. I can’t install the smaller ac drive belt. Only this belt will stretch if its being pulled by the terminator!

I’ll take it into the mechanics.
For now can I just keep driving the car without the AC belt or really needs to be on?

Post Reply